Klimaaufrüstung und RCD300 USB- fähig machen ??? Danke für alle Antworten

[Schattenparker14834]

Hi zamme,

bald bin ich auch besitzer eines Touran ( Bj. 2005 , 1.9 Higline DSG)

ein paar fragen hätte ich an euch:

kann man nachträglich eine climtronic einbauen, wenn nur eine climatic drinnen ist?? Wenn ja, wie viel wird das wohl ca . kosten??

Gab es den Higline auch mal ohne abgedunkelte Scheiben hinten

Gibt es eine Möglichkeit das RCD 300 von 2005 irgentwie MP3-Fähig zu machen?? Wenns geht mit VW Teilen. Wenn ja was kann das kosten??

Danke im Vorraus schon für alle Posts

Ferd

[Druckluftschrauber15358]

@ Oliver

Danke für die Kalkulation der Stunden.

Dann sind dies nach meiner Rechnung ca. 1500 Euro Lohnkosten.

Das ist mir dann im Moment doch etwas zuviel.

Zumal da auch noch das Material hinzu kommt.

LG

[Multimeter3522]

Hi!

Wo willst du das denn durchführen lassen?

Du kannst auch zu mir kommen!

Grüße
Oliver

[Druckluftschrauber15358]

Ich denke mal, daß es dann auch nicht billiger wird als hier vor Ort in der Vertragswerkstatt. Zumal bei Dir noch Übernachtung + Verpflegung hinzu kommt auch wenn man es als urlaub sehen könnte.

LG

[Multimeter11573]

Zitat:

Original geschrieben von Front

Hi!

Climatic zur Climatronic ist kein Problem!

Dauert zwar ein paar Stunden aber ist easy!

Du benötigst nur einen Climakasten (65 Euro Ebay)
und eine Climatronic Bedieneinheit (ab 40 Euro Ebay)

Grüße
Oliver

was meinst du denn mit "climakasten"

[Achsmanschette21301]

Hello,

I have a small problem that I trying to solve from more than 6 month. I have installed the same BT/USB adapter on RCD300 from Touran 2006.

Problem is that the devices are not communicating at all. When I push CD button twice, is sending me to cd-changer menu, but showing NO CDC. And reading with VCDS is giving me a fault that R41 cdchanger unit is not receiving any signal.

No I deactivated function again. Should I activate something else insted of cdchanger? Should I not activating it?

Thank you so much for any suggestion, because I  really don't know what to do it.

[gisbaert]

Control the ground from the interface - its a very small cable and sometimes there is no contact to the ground from car.

[axisminden]

yes, check the ground. to connect to ground you can use a screw at the backside from the rcd300.
That have works for me.

greetings

michael

[Achsmanschette21301]

Hallo,

I connected the ground, exactly on the back of RCD. without it the BT adapter is not working.

Problem is that both units are working, but no communication between, only TEL MUTE. And error in RCD that is no signal on r41 unit.

Thank you so much! 🙂 I am already fighting with this for more than 6 month.

[axisminden]

Ok this are two parts,
first can you pair your phone to the interface.?

do have the folder strukture that the interface need's?
the konfig.ini's are in Root of the USB stick?

do you have the Inferface for VW or the Interface for Market Radios?
For VW the number must be 7607545550001

greetings
Michael

[gisbaert]

O.K.- look for another software:
http://www.blaupunkt.de/index.php?...[view]=960

On this side go to "Anleitungen und weitere Informationen" - now you will see the sw updates.

[Achsmanschette21301]

Hello again,

Yes I can pair the phone to interface, it is a Motorola Defy. When I am calling is cutting the sound from radio speakers, but no voice transmitted.

config.txt file is in blaupunkt file in the usb stick. I followed Blaupunkt instructions...

I have the interface for VW, code name 7 607 545 550

below is the id.txt file content

Blaupunkt Bluetooth-USB-Interface 7 607 545 550
USB-Sta: 11 00 00 00 00 00
BT-ID: <0-19-61-0-A9-3D>
HW-VER: 8
SW-VER: 8625VW
BL-VER: 7732BL
SW-Sta: OK
P.Date: 7B10
P.Code: CN
Config: [CDC_BASIC][CFG_PB_ALL]
Created by Application SW8625VW

thank you so much again

[axisminden]

can you post the content of the Config.txt?

[Achsmanschette21301]

Yap, please find it below and thank you so much again 🙂

# Universal configuration 08.12.2008
# valid for Blaupunkt Bluetooth(BT)-USB-Interface VW 7 607 545 550
# SW8C01VW (01.12.2008) onwards
#
# > Copy / type all necessary configuration data into the
# Blaupunkt\config.txt file on your USB memory stick.
# > Syntax is [KEYWORD]=[PARAMETER].
# > Add or remove “#” in column 1 to (de)activate resp. parameter.
# > Use only CAPITAL letters in all configuration lines.
# > Lines starting with "#" are comments for your information
# without any effect on configuration.
#
# ======================================================
#
# Configure Bluetooth (BT) ON / OFF (default = ON)
#
# > BT enabled (if not disabled by below parameters) (default):
[BT_ON_OFF]=[ON]
#
# > This configuration will switch OFF all BT functions:
#[BT_ON_OFF]=[OFF]
#
# ======================================================
#
# Configure BT handsfree profile (HFP) ON / OFF (default = ON)
#
# > Hint: Operation of HFP needs [BT_ON_OFF]=[ON]!
#
[BT_HFP_ON_OFF]=[ON]
#[BT_HFP_ON_OFF]=[OFF]
#
# ======================================================
#
# Configure BT audio streaming profile (A2DP) ON / OFF (default = ON)
#
# > Hint: Operation of A2DP needs [BT_ON_OFF]=[ON]!
#
[BT_A2DP_ON_OFF]=[ON]
#[BT_A2DP_ON_OFF]=[OFF]
#
# ======================================================
#
# Configure BT compatibility mode:
#
# > for mobile phones requesting PIN after pairing
# to the interface (default)
[BT_COMP_MODE]=[OFF]
#
# > for mobile phones NOT requesting PIN after pairing
# to the interface
#[BT_COMP_MODE]=[ON]
#
# ======================================================
#
# Configure BT PIN number (for pairing):
#
# > PIN = 1234 (default)
[BT_USER_PIN]=[1234]
#
# > this will set PIN = 0000 (if enabled by removing "#"😉
#[BT_USER_PIN]=[0000]
#
# ======================================================
#
# Configure phonebook (PB) download:
#
# (*) if supported by mobile phone model
#
# > download all PB (*)(default)
[PB_DOWNLOAD_MODE]=[CFG_PB_ALL]
#
# > download PB from SIM card only (*)
#[PB_DOWNLOAD_MODE]=[CFG_PB_SIM]
#
# > download PB from mobile phone internal only (*)
#[PB_DOWNLOAD_MODE]=[CFG_PB_INT]
#
# > no PB download
#[PB_DOWNLOAD_MODE]=[CFG_PB_NONE]
#
# ======================================================
#
# Configure MIC test mode (installation test)
#
# > Normal operation, MIC test mode disabled (default):
[TEST_MIC_MODE]=[OFF]
#
# > MIC test mode enabled
# PTT toggles MIC-to-radio connection ON <-> OFF
# MIC test is OFF after switching radio to OFF and
# removing USB stick
#[TEST_MIC_MODE]=[ON]
#
# ======================================================
#
# Configure MIC gain
#
# > This parameter sets the MIC gain value [0]...[16]
# Default value is [8].
# Effect of gain adjustment may be partially
# compensated by BT echo canceller.
#
#[MIC_GAIN]=[8]
#
# ======================================================
#
# end of universal configuration file

[axisminden]

OK,
the file looks fine.
You have run the newest firmware. do you have try it with older one?
i would try to disable A2DP and Phonebook download.

[Achsmanschette21301]

Hallo,

Now I have SW8625VW. Should I try with 8C01?

I don't know the difference between these versions.

And I will do it this weekend, I am quite curious if it is the bt adapter or rcd problem. Should i do it with cd-changer option activate it?

Thank you again! 😉